Did you know that 1.03 million home invasions happen every year? Unfortunately, this troubling statistic is only getting worse which is why it’s important to have your ADT command panel up and working!
This means checking the battery and making sure it doesn’t need replacing. Unfortunately, most security companies don’t teach you how to replace your battery on an ADT command system. But don’t worry our guide is here to teach you how to do so!
What Happens if My Battery Dies?
Unfortunately, if your battery dies, so will your ADT command panel. This means your house will be unsecured for the time being. So it’s important to get an ADT command replacement battery as soon as possible!
Will My ADT System Still Work During a Power Outage
In the case of a power outage, your battery will not have the power to keep your system alive. So if you live in a populated area, make sure you have a generator.
And during bad weather like a snowstorm, your ADT system may experience some lagging. So ensure you have the best battery to keep your system well-fueled!
How Long Does an Alarm System Battery Last?
Depending on how well you take care of your system, an ADT battery can last 3 to 5 years. However, it’s important to clean the area at least once a month. This will avoid grime and dirt from forming which could cause your battery to die faster.
Why Is My ADT System Beeping?
If you have a dead or faulty battery, your alarm system will start making a beeping noise. This can very distracting, especially if you work from home. Luckily, there’s a way to silence your alarm before changing the battery. However, we do recommend you change the battery instead of silencing your system.
To silence your alarm, you can follow one out of the three methods below:
- Disable the system by entering your passcode
- Arm your system and promptly disarm it
- Hold the status button on the keypad
If none of these methods work, you may have other issues that are not battery-related. So call an ADT representative to ensure your system is in good standing!
Does an ADT Battery Recharge Itself?
After a power outage or replacement, most ADT batteries will need to recharge for at least 48 hours. However, the best ADT batteries can do this in just a few hours. Nevertheless, during the recharging stage, your home is still being protected.
I Replaced My Battery but My ADT System Is Still Not Working Properly
If your ADT system is still not working after a battery replacement, you’ll need to call your service provider to ensure there are no other issues. However, first, check your ADT keypad to ensure there isn’t a simple solution. Keep reading to learn more about this!
Why Is There a Trouble Light on My ADT Alarm?
If you’re seeing a yellow triangle on your ADT alarm system this means your system is having issues. Unfortunately, a trouble light can mean different things.
So you’ll need to press the number 2 on your ADT command keypad. The keypad will give you a number between 1 and 8. And you’ll need to look at your ADT command panel manual to know what the number means.
How to Replace Your Alarm System Battery
When your battery is low, your ADT command keypad will show ‘Lo Bat’. This means you’ll need a battery replacement. Most ADT command systems require a 12-volt Acid battery. However, check your ADT command panel manual for the most accurate battery replacement.
You’ll also need to know what size battery goes with your system, which will depend on your panel. So again you’ll need to check your ADT command panel manual.
Once you have the correct battery size and voltage, you can replace the old battery. Here are the steps you’ll need to follow to do so:
- First put your system into test mode to prevent false alarms
- Then log into MyADT.com and click on “My Alarm”
- A menu will appear then select “System Management”
- You’ll then click “place system on test.”
- Then open your system’s panel and gently disconnect the wires on your battery
- Place the new battery inside and make sure you connect the red wire on the red tab and the black wire on the black tab of your battery
- Once everything is properly connected, close the door panel
- Be aware that the low battery signal may show for at least 48 hours while the battery charges
Lastly, you’ll want to make sure your system is no longer in “test mode”. To do so, you’ll need to go to MyADT.com. Click on “My Alarm” under the “System Management” tab. Then click on “Stop Test“ and your system should be back to the correct mode.
How Do I Reset My ADT Command Panel after Changing the Battery?
After changing the battery, your security system may need to reboot. To do so, you’ll need to press the status button. Then enter your passcode and push the number 8. Lastly, you’ll be asked to enter the user code which is “1”.
Your ADT command should be up and working after this. However, if your system has still not rebooted, you’ll need to refer to your ADT command panel manual for more information!
Replace Your Battery Today
Remember that the security of your home should be your top priority. Luckily, now that you know how to replace your ADT command panel battery, you can have a betters night’s rest.
If you enjoyed this article, don’t forget to check out the rest of our website for similar content.
